Scholarly Works
Research Output
Recent Publications
Unified pseudo-static seismic reduction factors for shallow foundations via an earth-pressure framework
Publishing year: 2026
Journal article
Soils and Foundations, 2026, Volume 66, Issue 1
Scopus
This paper presents a unified and physically consistent method for evaluating the seismic bearing capacity of shallow foundations, based on classical earth pressure theory and a reinterpretation of the failure mechanism beneath the footing. The method builds on the key observation that the failure surface forms an angle of 45°+φ/2 with the footing (Zone I) and exits at 45°-φ/2 (Zone III), consistent with the geometry of active and passive earth pressures. Central to the analysis is the concept of a “virtual wall” extending downward from the footing edge to the log-spiral segment (Zone II) of the failure surface. Under seismic loading, the effective height of this virtual wall is reduced to account for the shallower failure mechanism. The framework is rigorously calibrated against the finite element method, in which the models are deliberately extended and lateral boundaries sloped on the failure side to prevent artificial reflection of seismic stresses. A distinctive feature of the proposed methodology is that all seismic reduction factors—cohesion, surcharge, and self-weight—are derived in a unified manner from a single physical mechanism. The resulting expressions are valid for any c-φ soil, and apply to both effective and total stress analyses. The reduction factors in the classical three N-bearing capacity formula are given as εc=εq=εH, εγ=εH2, with εH=1-kh/(tanφ+c/γHmax)0.2, where Hmax is the maximum depth of the failure mechanism. The method also incorporates the effect...
The Effect of Footing Shape on the Bearing Capacity of Shallow Foundations: A Review
Publishing year: 2025
Journal article
Archives of Computational Methods in Engineering, 2025, Volume 32, Issue 3
Scopus
Pages 1597-1617
This review paper examines the evolution of shape factors for the bearing capacity of shallow foundations, with a specific focus on rectangular and circular footings. Through a critical examination of methodologies from early empirical approaches to the sophisticated analyses enabled by recent technological advancements, this paper highlights the transformative impact of computational modeling on the field. Specifically, the review utilizes 3D finite element and finite difference analyses to validate and recalibrate shape factors against modern and reliable data. The quantitative findings confirm the reliability of the shape factors developed by Zhu and Michalowski in 2005 through classical finite element analysis in Abaqus. Their sγ factor, for example, was validated using Flac3D. Particularly notable is the finding that shape factors for circular footings can be effectively expressed by adjusting those for square footings using a simple geometric ratio, 4/π. This adjustment, based on the perimeter or area ratios of the two shapes, suggests a more efficient approach that challenges the necessity for distinct shape factors for different footing types. Additionally, the review highlights historical gaps such as non-documented factors from early empirical research, limitations due to the scale effects of small-scale tests, and assumptions supporting shape factors derived from limit analysis. It also emphasizes that depending on the aspect ratio of the footing and the friction a...
Stability evaluation of tunnels in steeply dipping layered rock mass using numerical models: a case study
Publishing year: 2025
Journal article
Scientific Reports, 2025, Volume 15, Issue 1
Repository
Tunnel stability is a critical factor in complex geological conditions, particularly in rock masses with steeply dipping layers. Among widely used methods, the Convergence-Confinement Method (CCM), a prevalent two-dimensional (2D) approach, effectively captures the relaxation process preceding support installation. However, most studies focus on homogeneous or horizontally layered rock masses, often overlooking the influence of steeply dipping, and layered geological formations. This study investigates the influence of layer dip angle and layer position on the stress relaxation factor (λ) and tunnel deformation through parametric analysis. The results indicate that λ increases with steeper dip angles, such as 60° and 90°, and decreases as the layers are positioned farther from the tunnel center, for instance, two tunnel widths above or below. Tunnel deformation is highly influenced by these factors, and the optimized λ values allow the 2D Convergence-Confinement Method (CCM) predictions to closely correlate with 3D simulation results. These findings enhance the applicability of the Convergence-Confinement Method (CCM) for tunnel stability analysis in steeply dipping, layered rock masses.
Nonlinear dynamic analysis of pile foundation using finite element method
Publishing year: 2025
Journal article
Scientific reports, 2025, Volume 15, Issue 1
Repository
Nonlinear dynamic response analysis of pile foundations is essential in seismic regions, where soil-pile-structure interaction governs safety and serviceability. Ethiopia's location along the African and Arabian tectonic plates exposes its infrastructure to high seismic risk, demanding rigorous foundation evaluation. This study investigates the pile foundations of Bridge B-40, part of the Awash-Kombolcha-Hara Gebeya railway project in the seismically active Afar Triangle (PGA = 0.3 g). Using PLAXIS 3D, with the Hardening Soil model at small strains and the Hoek-Brown model for rock, site-specific geotechnical and seismic data were incorporated to simulate static and dynamic conditions. Static analysis showed negligible settlement (0.55 mm), with stresses far below capacity. Free-field site response and free-vibration analyses established natural frequencies and captured seismic amplification effects. Under dynamic loading, ground accelerations varied between 24 and 136 cm/s2, and pile head displacement reached 91.24 mm, within structural limits. However, the maximum immediate settlement of 95.81 mm exceeded Eurocode serviceability criteria, signaling performance concerns despite adequate stability. Differential settlements between pile caps remained low (3.5-4.95 mm), and vertical stresses did not approach failure. These findings highlight the importance of nonlinear soil behavior in pile foundation design.
Bio-Based Plaster Composites Reinforced with Typha Angustifolia Fibers: Mechanical and Thermal Behavior for Energy-Efficient Building Envelopes
Publishing year: 2025
Journal article
Journal of Natural Fibers, 2025, Volume 22, Issue 1
Scopus
This study presents the development of sustainable plaster-based composite materials reinforced with Typha angustifolia fibers (TAF), aiming to improve thermal insulation and mechanical performance for lightweight wall systems in hot-arid climates. TAF is a regionally abundant wetland plant in Algeria, characterized by low density and high cellulose content, making it a promising natural reinforcement. Composites were prepared by partially replacing sand with 0–2% TAF by weight. Experimental results revealed that TAF incorporation reduced dry density and thermal conductivity, enhancing insulation properties while moderately decreasing compressive strength. Despite this reduction, the composites maintained adequate structural integrity for use in non-load-bearing walls and building partitions. Thermal simulations comparing TAF-based wall assemblies with conventional hollow concrete block systems under the climatic conditions of M’sila, Algeria, demonstrated improved thermal inertia, reduced heat flux, and more stable indoor temperatures. Annual energy analysis showed a relative improvement (reduction) of 21.1% in overall energy performance. These findings suggest that Typha-reinforced plaster composites can serve as effective bio-based building materials, supporting sustainable design and construction in arid and semi-arid environments.
An alternative sustainable desert-sand concrete incorporating industrial waste fillers: physicomechanical and microstructural insights
Publishing year: 2025
Journal article
Innovative Infrastructure Solutions, 2025, Volume 10, Issue 9
Scopus
The growing demand for sustainable construction materials has led to increased interest in utilizing industrial waste in concrete production. In particular, the replacement of conventional fillers with recycled materials presents both environmental and technical advantages. This study investigates the partial replacement of limestone filler (LF), with two powdered materials, waste glass powder (WGP) and waste expanded perlite (WEP), in desert sand concrete (DSC). The Design of Experiments technique was employed to assess the influence of these substitutions on the fresh and hardened properties of DSC, including workability, compressive strength, thermal conductivity, water absorption, and microstructure. Results showed that combining LF and WGP improved workability by up to 15.27%, while WEP tended to reduce it. Thermal conductivity was significantly reduced by WEP, achieving up to 15.29% reduction at full replacement. Compressive strength increased by up to 56% at 90 days with WGP, while ternary blends (LF–WGP–WEP) improved strength by 11.9%–24.85% compared to the control mix. Full replacement of LF with WGP also reduced water absorption by approximately 35.52%. SEM and EDX analyses revealed that WGP enhanced the microstructure and promoted C–S–H formation, contributing to reduced porosity and improved performance. These findings highlight the sustainable potential of reusing industrial waste in DSC to achieve both environmental and technical benefits. The approach supports...
68
Unique publications
36.8%
Open access (25 publications; 12 without information)
29.4%
With other institutions (20 publications; 19 without information)
H-Index Reports
| Index type | Scopus | Google Scholar | Web of Science |
|---|---|---|---|
| H-index | 12 | 15 | 1 |
| H5-index | 4 | 6 | 1 |
| H10-index | 8 | 10 | 1 |
Publications per year and source
No description yet.
- Faculty
- Faculty of Engineering and Technology
- Department
- Department of Civil Engineering and Geomatics