Scholarly Works
Research Output
Recent Publications
Photovoltaic limitations of FAPbI3 nanocrystal solar cells associated with ligand washing processes
Publishing year: 2024
Journal article
APL Energy, 2024, Volume 2, Issue 1
Repository
The processing of perovskite nanocrystals (PNCs) solar cells (SCs) usually incorporates ligand washing (LW) procedures. We show that a
LW step of FAI in EtAc assists in the removal of the oleic acid/oleylamine ligands and improves the JSC and FF values of FAPbI3 based SCs.
Although by increasing the exposure time of EtAc the removal of oleic acid/oleylamine ligands is more effective, sintering/necking of the
FAPbI3 results to NC agglomerations and formation of defects/traps are observed within the active layer by the reported photoluminescence
studies. Despite identifying the balanced in LW procedure exposure time, limitations on the performance of FAPbI3 PNCs SCs are reported.
To identify the photovoltaic limitations impedance spectroscopy studies are presented and show that in the case of FAPbI3 PNC SCs an
intermediate frequency response manifests. The observed impedance spectroscopy intermediate frequency response correlates with a parasitic
resistance effect, indicating charge transport limitations and charge recombination losses even after the applied LW processing procedure
Colloidal Perovskite Nanomaterials Processing and Photovoltaic Loss Analysis
Publishing year: 2022
Conference paper
Proceedings of nanoGe Spring Meeting 2022 (NSM22), 2022
Repository
In recent years, perovskite nanocrystals (PNCs) have attracted research interest for various optoelectronic applications that include light emitting diodes (LEDs) and solar cells 1. Several inherent material properties are desirable for both applications such as high photoluminescence quantum yield (PLQY), strong light absorption as well as the minimization of radiative recombination losses 2 3. Furthermore, PNCs show relatively high defect tolerance and tunability of the band gap by controlling the size and composition of the nanocrystals 4 5. In this work we compare photovoltaic (PV) devices based on (CH2(NH2))2PbI3 (FAPbI3) and CsPbI3 PNCs capped by oleic acid ligands. Specifically, we evaluate the influence of the processing conditions (ambient versus inert atmosphere and the effect of ligand washing (LW) steps on the photovoltaic (PV) performance of cells based on FAPbI3 and CsPbI3 PNCs. FaPbI3 PNCs shows increase in grain size upon the introduction of a ligand washing (LW) step based on formamidinium iodide (FAI) salt in EtAc due to ligand desorption and subsequent agglomeration of the NCs. Photovoltaic devices based on FAPbI3 PNCs provided a maximum PCE of 1.93% with the introduction of 3 LW steps with formamidinium iodide (FA) dissolved in ethyl acetate (EtAc) while CsPbI3 photovoltaic devices have provided PCE of 1.83 % using the same LW steps. The main photovoltaic performance limitation in both cases is the low Jsc and FF due to the high series resistance (Rs) w...
Exciton–Ligand Interactions in PbS Quantum Dots Capped with Metal Chalcogenides
Publishing year: 2020
Journal article
The Journal of Physical Chemistry C, 2020, Volume 125, Issue 50
Repository
Pages 27848-27857
Colloidal quantum dots (CQDs) are typically decorated with organic molecules that provide surface passivation and colloidal solubility. An alternate but less studied surface functionalization approach via inorganic complexes can produce stable CQDs with attractive transport and optical properties. Further development of such all-inorganic CQD solids is dependent on the deeper understanding of the energetic and dynamic interactions of the new ligands with the CQD excitons. Herein, a series of four metal chalcogenide (MCC) ligands of the KzXS4 type were attached to PbS CQDs. Out of the four MCC complexes studied, we find that only K4GeS4 ligands yield robust PbS CQD films with bright photoluminescence (PL) in the solid state. A systematic spectroscopic investigation of the K4GeS4-capped CQD films provides evidence of the temperature-dependent ligand-mediated exciton delocalization and trapping processes. At low temperatures, efficient trapping at ligand-induced states is found to occur within ∼6 ns after photoexcitation, followed by a considerably slower exciton back transfer to the CQD core. At elevated temperatures, the CQD films become photoconductive, providing evidence of exciton dissociation via carrier transfer within adjacent dots. The addition of a thin CdS shell suppresses the delocalization and trapping of excitons, resulting in brighter emission and significantly slower transient absorption and PL dynamics.
Printed Copper Nanoparticle Metal Grids for Cost‐Effective ITO‐Free Solution Processed Solar Cells
Publishing year: 2018
Journal article
Solar RRL, 2018, Volume 2, Issue 3
Repository
Copper nanoparticle inks have drawn much attention since they have the potential to constitute an alternative cost-effective solution than other noble metals nanoparticle inks such as Ag for indium tin oxide (ITO)-free printed electronic applications. Our research and development efforts have produced high conductivity copper nanoparticle inks which have excellent jetting and printing properties resulting in high quality inkjet-printed (IJP) Cu nanoparticle-based metal grids. We present ITO-free, Si-PCPDTBT: PC[70]BM organic photovoltaics (OPVs) processed in ambient low-cost fabrication conditions comprising for the first time embedded and non embedded inkjet-printed copper grid/Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the bottom electrode with power conversion efficiencies (PCE) of 2.56 and 3.35%, respectively. The results of the ITO-free OPVs using inkjet-printed Cu nanoparticle current collecting grids are discussed relevant to reference ITO-based OPVs with PCE of 4.92%.
Inkjet printing processing conditions for bulk-heterojunction solar cells using two high-performing conjugated polymer donors
Publishing year: 2014
Journal article
Solar Energy Materials and Solar Cells, 2014, Volume 130
Repository
Pages 474-480
We report the processing conditions for inkjet-printed active layers of organic photovoltaic (OPV) devices comprising bulk-heterojunction blends of the low bandgap conjugated polymer poly[(4,4′-bis(2-ethylhexyl)dithieno[3,2-b: 2′,3′-d]silole)-2,6-diyl-alt-(4,7-bis(2-thienyl)-2,1, 3-benzothiadiazole)-5,5′-diyl] (Si-PCPDTBT) as well as poly[N-9′-hepta-decanyl-2,7-carbazole-alt-5,5-(4′, 7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) used as electron donors with [6,6]-phenyl-C71-butyric acid methyl ester (PC 70BM) as electron acceptor. By controlling the inkjet printing processing conditions, we gain a significant improvement in device power conversion efficiency (PCE) to previously reported work using these materials. We obtain Si-PCPDTBT:fullerene and PCDTBT:fullerene-based inkjet-printed OPVs with power conversion efficiency of ~3% and ~4%, respectively.
Inkjet-printed polymer-fullerene blends for organic electronic applications
Publishing year: 2012
Journal article
Microelectronic Engineering, 2012, Volume 95
Repository
Pages 102-106
Organic field effect transistors, photodiodes and solar cells based on polymer-fullerene blend active layers are printed electronic applications under intense studies. We show that the viscosity of the inkjet formulation, substrate temperature, drop spacing and the height of the droplet in relation to the surface are critical parameters to achieving high quality inkjet-printed polymer-fullerene based active layers. The effect of the above processing parameters on the performance of polymer-fullerene based organic solar cells is presented
7
Unique publications
28.6%
Open access (2 publications; 1 without information)
85.7%
With other institutions (6 publications; 1 without information)
H-Index Reports
| Index type | Scopus | Google Scholar | Web of Science |
|---|---|---|---|
| H-index | 3 | 3 | 0 |
| H5-index | 1 | 0 | 0 |
| H10-index | 2 | 1 | 0 |
Publications per year and source
No description yet.
- Faculty
- Faculty of Engineering and Technology
- Department
- Department of Mechanical Engineering and Materials Science and Engineering
- Title
- Assistant Professor