Scholarly Works
Research Output
Recent Publications
Soil Effects on Structural Integrity of Large Diameter Offshore Wind Turbine Substructure Using Finite Element Analysis: A Comparative Study
Publishing year: 2026
Conference paper
Journal of Physics Conference Series, 2026, Volume 3253, Issue 1
Scopus
The focus on renewable energy development has led to increase in the number of offshore wind turbines. As these structures are subjected to harsh environmental conditions in deep seas and different locations, there is a need to consider the structural integrity of their support structure. Thus, a numerical analysis is employed in this study to access the effects of the soil profiles on the stress evolution in the support structure of a 15 MW large-diameter offshore wind turbine in peak power production conditions. Finite element analysis has been applied to real soil profile parameters obtained from in-situ soil tests in the North Sea, East China Sea, and Irish Sea. Due to the huge size of the structure, a modal analysis was also conducted to determine the natural frequency of the structure. Additionally, the effect of soil type and location on lateral response was considered. The inclusion of soil model provided realistic performance as natural frequency in different soils was within expected frequency band while maximum deformation of 2.8 m was observed at the tower top. Stress evolution results in all models showed a maximum difference of 9.5 % with compressive stresses being dominant in the splash zone of the transition piece of the OWT. The medium to dense sand soil profile in the North Sea provided good structural performance over the rest soil profiles considered
Predictive framework for corrosion-fatigue life assessment of large offshore wind turbine monopiles using real environmental data
Publishing year: 2026
Journal article
Ocean Engineering, 2026, Volume 362
Scopus
Corrosion-fatigue is a major challenge for the safe and economical operation of offshore wind turbines supported by large monopiles. This paper presents a new predictive framework that combines real wind and wave data with wind-speed-dependent load modelling, analytical beam theory and finite element analysis, soil-structure interaction for North Sea conditions, and corrosion-fatigue modelling based on pit morphology and mean stress effects. The framework uses cumulative damage assessment to estimate the remaining life and is demonstrated on the IEA 15-megawat turbine with data from Westermost Rough in the UK. Rotor thrust is identified as the dominant load, reaching 2.563 MN at the rated wind speed of 10.59 m/s. Corrosion-induced thickness loss, based on DNVGL-RP-0416 rates, increases stresses over time and shifts the critical region from the submerged zone to the splash zone after about seven years. Tensile stresses rise from 76 to 81 MPa in the submerged zone and from 74 to 87 MPa in the splash zone. The analytical beam theory and finite element models showed close agreement in stress prediction, with an average difference of 3.64%, confirming the reliability and scalability of the adopted methods. A pit corrosion factor (0.332 ≤ f c ≥ 0.578), derived from X-ray computed tomography measurements and notch theory, is used in a fatigue model validated against welded S355J2+N and S355G10 + M steels, including specimens corroded in seawater for six months and tested to BS EN IS...
Fabrication and characterisation of biomimetic porous materials using diffusion-generated images and additive manufacturing
Publishing year: 2026
Journal article
Results in Materials, 2026, Volume 32
Scopus
Biological porous materials exhibit complex architectures that are challenging to design using conventional modelling approaches. This study presents a reproducible workflow that integrates prompt-driven diffusion image generation with additive manufacturing to fabricate biomimetic porous polymer structures. A general pre-trained diffusion model was used to generate two-dimensional image slices imitating natural porous materials, while a fine-tuned model conditioned on X-ray microtomography data was employed to generate hybrid-like morphologies. Four strategies for image-to-geometry were investigated resulting in controlled 2.5D and quasi-3D porous architectures. The structures were manufactured using fused deposition modelling and characterized in terms of density, pore size distribution, and compressive response. The results demonstrate that accessible diffusion-based image generation, combined with appropriate workflows enables practical exploration of biomimetic porous materials. It also highlights limitations by comparison to volumetric generative models.
Submerged Arc Welding of S355G10+M Steel: Analyzing Strength, Distortion, Residual Stresses, and Fatigue for Offshore Wind Applications
Publishing year: 2025
Journal article
Fatigue and Fracture of Engineering Materials and Structures, 2025, Volume 48, Issue 9
Scopus
Pages 3859-3878
This research delves into the material performance of submerged arc-welded S355G10 +M structural steel for offshore wind turbines, with an emphasis on strength, ductility, hardness, distortion, residual stress, and fatigue. This was done by conducting experiments and employing modeling tools combined with image analysis. The novelty of this study lies in examining the effects of material properties of S355G10 +M structural steel used in welded offshore wind turbine tower and monopile. The study employed a submerged arc welding (SAW) process on S355G10 +M plates of varying thicknesses by applying double V-groove and multi-pass technique. Tensile tests revealed that welded sections exhibit greater ultimate tensile strength than the base material, despite the lower yield strength. In addition, hardness and residual stresses correlate with thickness, and a potential weak point is observed at the heat-affected zone (HAZ) and base material transition. Angular distortions and axial misalignments after welding, as well as stress concentrations and residual stresses, were found to affect the fatigue performance. It was concluded that the conducted welds have sufficient quality to be exploited into industrial marine applications including offshore wind turbines.
Quality Certification in Data Acquisition for Cultural Heritage: The Power of Paradata for High Quality Digital 3D Cultural Heritage Assets
Publishing year: 2025
Journal article
International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences - ISPRS Archives, 2025, Volume XLVIII-M-9-2025
Repository
Published in 2022, the European Commission’s study VIGIE 2020/654: Study on Quality in 3D Digitisation of Tangible Cultural Heritage provided a comprehensive overview of the state-of-the-art in Cultural Heritage (CH) digitisation, proposing detailed guidelines toward a standardised framework for evaluating digitisation projects. The Study introduced a key distinction between the Complexity of the data acquisition methodology and the Quality of the expected results. It argued that Quality can only be meaningfully assessed by understanding the preconditions - namely, the Complexity - surrounding data acquisition (DAQ). By managing risks, faithfully documenting paradata (i.e., the processes and methods used to create the digital record), and reducing DAQ complexity, confidence in the digitisation outcomes is increased and better reflected in the overall Quality of results.
In the rapidly evolving landscape of digital technologies and their application to the CH domain, alongside the growing need to monitor monuments and sites affected by natural and human-induced hazards and interventions, this article reflects on three years of real-world implementation. It reviews the lessons learnt, identifies existing gaps, and explores emerging technologies to enhance and adapt the Study to the current and future needs of the sector. These insights are essential to ensure the continued relevance and effective adoption of the Study’s recommendations.
Preface
Publishing year: 2025
Journal article
Lecture Notes in Computer Science Including Subseries Lecture Notes in Artificial Intelligence and Lecture Notes in Bioinformatics, 2025, Volume 15190 LNCS
Scopus
Pages v-vii
37
Unique publications
70.3%
Open access (26 publications; 4 without information)
45.9%
With other institutions (17 publications; 6 without information)
H-Index Reports
| Index type | Scopus | Google Scholar | Web of Science |
|---|---|---|---|
| H-index | 12 | 13 | 1 |
| H5-index | 7 | 9 | 1 |
| H10-index | 10 | 11 | 1 |
Publications per year and source
No description yet.
- Faculty
- Faculty of Engineering and Technology
- Department
- Department of Mechanical Engineering and Materials Science and Engineering
- Title
- Dr