Scholarly Works
Research Output
Recent Publications
Recovery of bioactive compounds and manufacture of bacterial cellulose nanocrystals from citrus processing wastewater: An integrated biorefinery approach
Publishing year: 2026
Journal article
International Journal of Biological Macromolecules, 2026, Volume 337
Scopus
Although citrus processing wastewater is rich in bioactive compounds and nutrients, the significant potential of the specific feedstock for valorization still remains largely unexploited. Thus, a citrus processing wastewater-based biorefinery was employed to recover carotenoids and polyphenols, while producing microbially derived bacterial cellulose nanocrystals. The solid fraction of the effluent was applied in solid-liquid extraction using various green- and petrochemical-based solvents, yielding 1.97 ± 0.03 mg of carotenoids per g of dry solid via a mixture of D-limonene/ethanol/acetic acid. A continuous adsorption/desorption system was developed, adsorbing 89.1 ± 0.63% (w/v) of the initial phenolic content. Different solvents were assessed as elution agents maximizing the desorption of the phenolic content (76 ± 7.25%, w/v) using 75% ethanol. The remaining sugar-rich liquid was subsequently utilized for bacterial cellulose manufacture employing Komagataeibacter sucrofermentans DSM 15973. Elevated fermentative production was achieved at pH-value 6.0 using a surface-to-volume ratio of 1.53 cm−1, yielding 4.98 ± 0.28 g L−1 of the biopolymer following 6 d of incubation. The bacterial cellulose formed was processed using sulfuric acid, aiming to hydrolyze the amorphous fraction and produce a biomaterial of higher crystallinity as well as enhanced stability and mechanical properties as compared to the pristine biopolymer. The nanocrystals produced exhibited colloidal stability...
Plasma-induced functionalization of graphitic surfaces: The role of nitrogen–argon gas mixtures
Publishing year: 2026
Journal article
Materials Chemistry and Physics, 2026, Volume 348
Scopus
Graphite-based materials are crucial in state-of-the-art technologies, including energy conversion, energy storage and sensing, due to their exceptional electrical conductivity, stability and versatility. Tailoring their surface properties through environmentally friendly techniques is essential for optimizing their performance in diverse applications. This study investigates the effects of low-frequency plasma treatment on high-purity mineral graphite using various mixtures of nitrogen and argon gases. Plasma treatment was employed to systematically modify the surface properties and incorporate nitrogen functionalities. Advanced characterization methods, including scanning electron microscopy, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and gas sorption analysis, were used to evaluate changes in morphology, chemical composition, microstructure and porosity/surface area. Plasma-treated samples exhibited notable surface restructuring, including thinner platelets, with minimal alterations to the overall pore structure. Nitrogen doping was achieved with nitrogen concentrations reaching 5.8 at.% for the 100 % nitrogen plasma-treated sample, primarily as pyridinic and graphitic nitrogen, enhancing the material's catalytic and electronic properties. While slight structural disorder and defect formation were observed, the fundamental graphitic framework remained intact. This work provides valuable insights into the functionalization mechanisms and highlig...
Pilot-scale production of high-purity struvite fertilizer from livestock waste: Outcomes of the RE-LIVE WASTE project in Cyprus
Publishing year: 2025
Journal article
Journal of Environmental Management, 2025, Volume 393
Repository
Decarbonizing fertilizer production necessitates the development of innovative practices for producing waste-derived fertilizers, that will mitigate environmental degradation from waste disposal. Struvite crystallization (SC) is a well-known practice for nutrient recovery from waste by producing struvite (MgNH4PO4·6H2O) fertilizers. However, research on SC upgrading from livestock waste is limited. In this study, experiments were conducted in the Cyprus 250-L SC pilot reactor. Ultrafiltration permeates from mixed livestock, dairy, and bio-wastes, Matrix 1, and pig slurry, Matrix 2, were used separately to crystallize struvite with pure magnesium hydroxide (Mg(OH)2). Additionally, Matrix 1 was subjected to SC using technical grade magnesium oxide (T.G. MgO). Matrix 1 was first evaluated as matrix in pilot-scale SC. XRD results indicated that using T.G. MgO and Matrix 1 in SC yielded the highest struvite purity, 99.6 % w/w. However, XRF showed that iron (Fe), manganese (Mn), and nickel (Ni) in the precipitate exceeded limits. Struvite precipitates produced using Mg(OH)2 were of high purity, 89.2 %-98.0 % w/w. SEM-EDX analysis revealed mainly orthorhombic, prismatic, and octahedral struvite crystals up to 200 μm. The precipitates met regulatory standards for pathogens, carcinogens, and heavy metals, and contained beneficial plant macronutrients and micronutrients within limits. Εconomic analysis for a 200 m3 scale-up process using Matrix 1 and Mg(OH)2 showed viability, yielding...
Experimental investigation of the tensile properties of steel foam hollow sphere assemblies
Publishing year: 2025
Journal article
Journal of Materials Research and Technology, 2025, Volume 39
Repository
Pages 7588-7612
The present research aims to study the mechanical properties of steel foam hollow sphere assemblies of various relative densities under the effect of uniaxial tensile loading, evaluating the validity of a new test protocol and comparing it with other experimental results. Through a series of experiments with different groups of specimens, which were recorded step by step, the effects of factors such as the relative density and the number of bonds on the mechanical properties of the specimens were identified, and their impact on the response discussed. The shape of the specimen is cubic with dimensions 50 × 50 × 50 mm3. The range of values recorded in this research for the Elastic Modulus is 340,89–399,28 MPa, and for Tensile Strength is 2,8-3,53 MPa, as exhibited by the five different groups of specimens tested in the present study with relative density from 0,059 to 0,074. The promising experimental results support the proposed methodology and test protocol for studying similar assemblies under tensile loading and an attempt to explain the differences between past scaling equations and experimental results. Scanning electron microscopy (SEM) is also performed and presented to examine the microstructure of the specimens and the crack surface.
Advanced manufacture of polyphenols, essential oils and bacterial cellulose in a novel citrus processing wastewater biorefinery
Publishing year: 2025
Journal article
Journal of Environmental Management, 2025, Volume 374
Scopus
Herein, a citrus processing wastewater-based biorefinery has been developed manufacturing essential oils, polyphenols and bacterial cellulose. Liquid-liquid extraction was evaluated for isolation of essential oils assessing different organic solvents, recovering 0.45 kg of essential oils per m3 of wastewater using n-heptane. Amberilte® XAD4, XAD16N and XAD7HP, PurSorb™ PAD900, biochar and activated biochar were compared as adsorbents for polyphenols recovery, demonstrating that the adsorption isotherms of the resins applied could be closely predicted using the Langmuir model. Adsorption and desorption density experiments exhibited that the phenolic content present in citrus processing wastewater could be efficiently recovered using PAD900, yielding 0.78 kg of polyphenols per m3 of wastewater. The sugar content remaining following polyphenols adsorption was applied for bacterial cellulose production employing Komagataeibacter sucrofermentans DSM 15973 determining the biopolymer's production efficiency as well as morphological and structural properties at different carbon to free amino nitrogen ratios. The higher content of the biomaterial was obtained employing 15.0 carbon to free amino nitrogen ratio, which yielded 4.4 kg of biopolymer per m3 of wastewater. The study has shown that by decreasing the carbon to free amino nitrogen ratio could enable enhancing the water-holding capacity of bacterial cellulose, exhibiting that the control of fermentation conditions could potentia...
The Roles of Impurities and Surface Area on Thermal Stability and Oxidation Resistance of BN Nanoplatelets
Publishing year: 2024
Journal article
Nanomaterials (Basel, Switzerland), 2024, Volume 14, Issue 7
Repository
This study considers the influence of purity and surface area on the thermal and oxidation properties of hexagonal boron nitride (h-BN) nanoplatelets, which represent crucial factors in high-temperature oxidizing environments. Three h-BN nanoplatelet-based materials, synthesized with different purity levels and surface areas (~3, ~56, and ~140 m2/g), were compared, including a commercial BN reference. All materials were systematically analyzed by various characterization techniques, including gas pycnometry, scanning electron microscopy, X-ray diffraction, Fourier-transform infrared radiation, X-ray photoelectron spectroscopy, gas sorption analysis, and thermal gravimetric analysis coupled with differential scanning calorimetry. Results indicated that the thermal stability and oxidation resistance of the synthesized materials were improved by up to ~13.5% (or by 120 °C) with an increase in purity. Furthermore, the reference material with its high purity and low surface area (~4 m2/g) showed superior performance, which was attributed to the minimized reactive sites for oxygen diffusion due to lower surface area availability and fewer possible defects, highlighting the critical roles of both sample purity and accessible surface area in h-BN thermo-oxidative stability. These findings highlight the importance of focusing on purity and surface area control in developing BN-based nanomaterials, offering a path to enhance their performance in extreme thermal and oxidative conditions...
122
Unique publications
32.8%
Open access (40 publications; 33 without information)
48.4%
With other institutions (59 publications; 39 without information)
H-Index Reports
| Index type | Scopus | Google Scholar | Web of Science |
|---|---|---|---|
| H-index | 31 | 35 | 1 |
| H5-index | 11 | 11 | 1 |
| H10-index | 23 | 25 | 1 |
Publications per year and source
No description yet.
- Faculty
- Faculty of Engineering and Technology
- Department
- Department of Mechanical Engineering and Materials Science and Engineering
- Title
- Associate Professor